Cart 0

How Much Does a New Furnace Cost? (2026 Price Guide)

What a new furnace really costs, from the unit price to installation, and the factors that push the total up or down.
Modern residential gas furnace beside a digital display showing the 2026 Furnace Cost Guide with pricing blueprint in a clean home utility room.

How much does a new furnace cost? In 2026, most homeowners pay between $3,000 and $7,600 for a furnace installed, with the national average landing near $4,800. The furnace unit alone typically runs $1,200 to $3,500, while labor, venting, and removal make up the rest. Your final price depends on fuel type, size, efficiency (AFUE), and install complexity.

Flat vector infographic comparing equipment-only cost and professionally installed cost for 80 percent and 96 percent AFUE gas furnaces.

Comparison chart illustrating the difference between equipment-only and installed costs for standard and high-efficiency gas furnaces.

That’s the short answer. But “average” hides a lot. A basic 80% AFUE gas furnace for a small home is a very different purchase than a modulating 96% condensing unit for a 3,000-square-foot house. Below, we break down new furnace cost by every factor that moves the number—and, importantly, we separate the equipment cost (what the furnace itself costs) from the installed cost (equipment plus labor). That distinction matters, because buying your furnace direct at wholesale pricing is one of the biggest levers you control.

Equipment-Only vs. Installed Cost: Why the Split Matters

Most furnace cost guides lump everything into one big “installed” number. That’s convenient, but it obscures where your money actually goes—and where you can save.

A typical residential furnace replacement breaks down roughly like this:

Cost componentTypical rangeShare of total
Furnace unit (equipment)$1,200 – $3,500~40–55%
Labor (installation)$1,200 – $2,500~30–40%
Venting, gas line, electrical$300 – $1,200~8–15%
Permits & inspection$50 – $400~2–5%
Old furnace removal/disposal$50 – $500~2–5%

The equipment is the single largest line item—and it’s the one with the widest price spread between retail and wholesale. When you buy a furnace through a traditional full-service HVAC company, the unit is often marked up significantly before labor is even added. Buying the same equipment direct lets DIY-capable homeowners and contractors capture that margin instead.

Key Takeaway

National Air Warehouse ships gas furnaces and complete HVAC systems at manufacturer-direct, wholesale pricing with free shipping—so the equipment portion of your project costs less from the start. You still pay for professional installation (which we strongly recommend for gas and venting work), but you’re not paying a retail markup on the hardware.

New Furnace Cost by Size (BTU Output)

Furnaces are sized by heating output, measured in BTUs per hour (BTU/h). The right size depends on your home’s square footage, climate zone, insulation, and ceiling height—which is why a proper Manual J load calculation beats any square-footage rule of thumb. Oversizing wastes money and causes short-cycling; undersizing leaves you cold on the worst nights.

That said, here are realistic equipment-only ranges by output:

Furnace size (BTU/h)Typical home sizeEquipment-only priceInstalled price
40,000 – 60,0001,000 – 1,500 sq ft$1,000 – $2,400$2,800 – $5,000
60,000 – 80,0001,500 – 2,200 sq ft$1,300 – $3,000$3,200 – $6,200
80,000 – 100,0002,200 – 2,800 sq ft$1,700 – $3,500$3,800 – $7,000
100,000 – 120,000+2,800 – 3,500+ sq ft$2,200 – $4,200$4,500 – $8,500

Note that “home size” is a loose guide. A well-insulated 2,500-sq-ft home in a mild climate may need less heating output than a drafty 1,800-sq-ft home in the upper Midwest. Always confirm sizing with a load calculation rather than guessing.

New Furnace Cost by Fuel Type

Fuel type is one of the biggest cost drivers—both for the equipment and for what you’ll pay to run it for the next 15–20 years.

Gas Furnaces

Natural gas furnaces are the most common choice in the US and usually offer the lowest operating cost where gas is available. Equipment runs roughly $1,200–$3,500, with installed costs of $3,000–$7,600 depending on size and efficiency. They require proper venting and a gas connection, which is why professional installation is essential.

Electric Furnaces

Electric furnaces have the lowest upfront equipment cost—often $800–$2,500—and simpler installation (no gas line or combustion venting). Installed cost frequently lands between $2,000 and $4,500. The catch is operating cost: in much of the country, resistance-electric heat is more expensive to run than gas. In moderate climates, a heat pump is usually a smarter electric option.

Oil Furnaces

Oil furnaces are concentrated in the Northeast. Equipment typically costs $2,000–$4,500, with installed prices of $4,500–$9,000. They require an oil storage tank and more frequent maintenance, and fuel prices can be volatile.

Propane Furnaces

Propane units are mechanically similar to natural gas furnaces and use comparable equipment (often the same units with a conversion kit). Installed cost generally runs $3,500–$7,500. Propane is common for rural homes without natural gas service, but the fuel itself tends to cost more per BTU.

Fuel typeEquipment-onlyInstalledBest for
Natural gas$1,200 – $3,500$3,000 – $7,600Lowest operating cost where gas exists
Electric$800 – $2,500$2,000 – $4,500Low upfront cost, no gas line
Oil$2,000 – $4,500$4,500 – $9,000Northeast homes on oil
Propane$1,400 – $3,800$3,500 – $7,500Rural/off-grid, no natural gas

 

Modern high-efficiency condensing gas furnace with white PVC vent pipe installed in a clean residential utility room.

A professionally installed condensing gas furnace featuring PVC vent piping and condensate drainage for high-efficiency home heating.

New Furnace Cost by Efficiency (AFUE) and Stage

Understanding AFUE

A furnace’s efficiency is measured by AFUE—Annual Fuel Utilization Efficiency. An 80% AFUE furnace converts 80% of its fuel into usable heat and sends the other 20% up the flue. A 96% AFUE furnace wastes only 4%. Higher AFUE means a higher purchase price but lower monthly fuel bills.

A key dividing line: furnaces at 90% AFUE and above are “condensing” furnaces. They extract extra heat from exhaust gases, which produces acidic condensate and cool exhaust. That means they vent through PVC pipe (often out a sidewall) and need a condensate drain—sometimes adding install cost if you’re upgrading from an 80% unit. The US Department of Energy explains AFUE ratings in more detail at energy.gov, and you can identify high-efficiency models by the ENERGY STAR label.

Understanding Staging

Beyond AFUE, furnaces come in three burner configurations:

  • Single-stage: one heat output level (full blast or off). Lowest cost, more temperature swing.
  • Two-stage: high and low settings, so it runs gently most of the time. Better comfort and quieter.
  • Modulating: adjusts output in small increments for the most even temperatures and highest efficiency. Most expensive.
Efficiency / stage tierAFUEEquipment-onlyNotes
Standard, single-stage80%$1,000 – $2,200Lowest cost; metal flue venting
High-efficiency, single-stage90–95%$1,500 – $2,800Condensing; PVC venting required
High-efficiency, two-stage95–96%$2,000 – $3,400Better comfort, lower bills
Premium, modulating96–98%$2,800 – $4,500+Quietest, most even heat
Is High-Efficiency Worth It?

If you live in a cold climate with high heating bills, the fuel savings from a 95%+ furnace can pay back the price difference over the unit’s life. In a mild climate where the furnace runs only a few months a year, a quality 80% unit may make more financial sense. Note that some regions and states have minimum AFUE requirements, so check local codes before buying an 80% unit.

What Drives Installation Cost

Even with the same furnace, two homes can see very different install quotes. The main factors:

  • Labor rates vary by region and company—expect $1,200–$2,500 for a straightforward swap, more for complex jobs.
  • Ductwork in poor condition may need repair, sealing, or modification. Major duct rework can add $1,000–$5,000.
  • Venting changes are common when moving from an 80% to a 90%+ condensing furnace, since you switch from metal flue to PVC and add a condensate drain.
  • Gas line or electrical upgrades may be required if capacity is insufficient.
  • Permits and inspection are typically required and run $50–$400.
  • Old unit removal and disposal adds $50–$500.
  • Accessibility—a cramped attic or crawlspace install costs more than a basement swap.
Two certified HVAC technicians installing a residential gas furnace, connecting venting and using power tools during installation.

Certified HVAC professionals completing a residential gas furnace installation with precision and expert craftsmanship.

This is also where buying equipment direct helps: when you supply your own wholesale furnace, you can hire an installer for labor only, avoiding the markup bundled into all-in quotes. Many contractors are happy to do labor-only installs; just confirm before you buy.

Signs You Need a New Furnace

Replacing proactively often beats an emergency breakdown in January. Watch for:

  • Age over 15–20 years: most furnaces last 15–25 years; older units are far less efficient than modern equipment.
  • Rising heating bills despite no rate changes—a sign efficiency is dropping.
  • Frequent repairs, especially when a single repair approaches half the cost of replacement.
  • Uneven heating or rooms that never warm up.
  • Yellow burner flame, soot, or excessive cycling—possible combustion issues.
  • A cracked heat exchanger, which is a carbon monoxide safety hazard and almost always means replacement.

If you’re seeing several of these, it’s worth pricing a replacement before peak season—both for safety and savings.

How to Save on a New Furnace

You have more control over furnace cost than most guides admit. The biggest levers:

  1. Buy your equipment direct at wholesale. The furnace is the largest line item. Purchasing manufacturer-direct from National Air Warehouse with free shipping removes the retail markup, then you pay an installer for labor only.
  2. Shop in the off-season. Demand and prices for heating equipment often soften in late spring and summer. Buying ahead of winter avoids emergency premiums.
  3. Right-size, don’t oversize. A correctly sized furnace costs less to buy and run. Insist on a load calculation.
  4. Claim rebates and tax credits. High-efficiency and ENERGY STAR furnaces may qualify for federal tax credits and utility rebates. Check current federal incentives at energy.gov and your local utility’s program before buying.
  5. Match efficiency to your climate. Don’t overpay for a 98% modulating furnace if you live where the heat runs two months a year.

Contractors: if you install regularly, NAW offers dedicated wholesale HVAC pricing for contractors on furnaces and full systems—volume pricing with the same free shipping.

Frequently Asked Questions

How much does a new furnace cost installed in 2026?

Most homeowners pay $3,000–$7,600 for a new furnace installed, averaging around $4,800. The unit itself is $1,200–$3,500; the rest is labor, venting, permits, and removal. Fuel type, size, and efficiency all shift the final price.

How much does just the furnace unit cost without installation?

Equipment-only prices typically range from $800 for a basic electric furnace to $4,500+ for a premium modulating gas furnace. Most standard residential gas furnaces fall between $1,200 and $3,500. Buying direct at wholesale lowers this line item significantly.

Is a 96% AFUE furnace worth the extra cost over an 80%?

In cold climates with high heating bills, the fuel savings from a 95–96% furnace often justify the higher price over the unit’s 15–20 year life. In mild climates, a quality 80% furnace may be more economical—though some regions require 90%+ by code.

How long does a furnace last?

Most furnaces last 15–25 years with regular maintenance. Efficiency declines with age, so units past 15 years are often worth replacing—especially if repairs are getting frequent or expensive.

Can I buy a furnace myself and hire someone to install it?

Yes. Many homeowners and contractors buy equipment direct at wholesale and hire a licensed installer for labor only, avoiding retail markup. Confirm your installer accepts customer-supplied equipment, and always use a pro for gas and venting work.

The Bottom Line

A new furnace in 2026 typically costs $3,000–$7,600 installed, but your actual price hinges on fuel type, size, efficiency, and install complexity. The single biggest cost you can control is the equipment itself—and that’s exactly where buying direct pays off.

Browse gas furnaces and complete HVAC systems at National Air Warehouse for manufacturer-direct pricing with free shipping, or request wholesale contractor pricing if you install for a living. Either way, you’ll see real numbers before you commit.

Your growth is the mission.

National Air Warehouse ships gas furnaces and complete HVAC systems at manufacturer-direct, wholesale pricing with free shipping, helping homeowners and contractors cut the cost of every install. Shop gas furnaces or contact our team for help picking the right system.